Got bored. Pulled the hatch.. The mid spoiler is now mounted Pics later.
Announcement
Collapse
No announcement yet.
Awd mp5
Collapse
X
-
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
-
Needs more work. At least it's mounted though.
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
It's not all thaaat bad. Basically a rip off of the GTR spoiler. I like it.. Downside is the hatch is garbage without now. A good highway trip should allow me to determine whether or not it's going to be an improvement or a problem. Need to remove the tint while I have it out
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
More pics
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
Started messing with the exhaust a little bit tonight. It looks like at this point that my stuff from the egt will work without much work. So far it looks like I'll only need to take about 4" from the very rear between the muffler and the subframe section. I may need to lengthen it up front around 4" when I go to redo my downpipe. Not bad.. less work makes me happy! Will be ordering some new Tokico blues / Tokico springs for it. Need to redo the braking system completely.. Need to pick up a probe/626 subframe and lca's. The list goes on. Lots more work to come
Old pics of my exhaust. zx2 trubendz 2.5" kit thats slightly modified.
Last edited by jinx; 12-14-2012, 01:09 AM.
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
Got a lil further on the exhaust! However, I need to shorten it in a few areas. Nothing major. It's just a tighter setup then the BG was.
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
After fussing with the exhaust some, I'm leaning towards getting a fuel cell for it now. I'd likely end up having to do it when I start doing the awd conversion anyways.
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
is the fuel tank that much in the way??? any pictures of the OE routing on that beast?---Has ClubProtege helped you in someway? show your support by Contributing--- Click Here---
1992- project FE3..... 313 WHP @ 9.3psi
I pet my dash when I get into the car..."good car"he actually has a mazda tree, parts grow on it
Comment
-
Originally posted by MazdaNoob View PostDual tip centered exhaust ?
Originally posted by FE3-323 View Postis the fuel tank that much in the way??? any pictures of the OE routing on that beast?
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
it can be semi expensive. but have you looked into oval tubing in the tighter areas of the tunnel? that'll help give you alot more clearance for the driveshaft---Has ClubProtege helped you in someway? show your support by Contributing--- Click Here---
1992- project FE3..... 313 WHP @ 9.3psi
I pet my dash when I get into the car..."good car"he actually has a mazda tree, parts grow on it
Comment
-
Looks like I'll be busy at least for a lil while.. I bought an Arduino to toy with!
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
-
no clue what that is, but all the luck man lol.
P.S. got those rear strut bar brackets finally, just gotta get em boxed up and they'll be out hopefully tomorrow or monday-Jack
ONTARIO MAZDA CLUB! Join! https://www.facebook.com/groups/500055016671733/
91 626 LX - basically stock and pretty slow still
http://www.clubprotege.com/forum/sho...my-GD-626-LX-)
01 E53 3.0i - FOR SALE! pm if interested
91 USDM Protege LX - SOLD! turbo/manifold up for sale!
http://www.clubprotege.com/forum/showthread.php?t=46606
Comment
-
Originally posted by Mazda_Powered View Postno clue what that is, but all the luck man lol.
P.S. got those rear strut bar brackets finally, just gotta get em boxed up and they'll be out hopefully tomorrow or monday
HPLogic Mustang Dyno @ 15psi on MS1 v3 226 whp / 195 ft-lb [HD Video]
Soon to be powered by a Precision snail on crack...
Add me on more pictures of my projects can be found there.
Comment
Comment